How to Reset a Nest Hello Video Doorbell

Introduction

This guide will assist you in performing a factory reset on your Nest Hello Video Doorbell. You may wish to do this if your device is not working as intended and you've exhausted all other possible repair steps or you want to give it to someone else.

Factory resetting your camera will erase all your camera’s settings and options. It will not automatically reconnect to Wi-Fi.

You will need:

  • The release tool (or unfolded paper clip)

1 Remove Device from Nest Account

You can remove your Nest device (Thermostat, Cam, Dropcam, etc) from your Nest Account within the Nest app. Whether you’re using a computer or mobile phone, the steps are the same.

  1. To remove a Nest device from your Nest Account, log into your account with the Nest app.
  2. If you have multiple homes registered on the app, tap the Menu icon in the top left corner of the app home screen, then select the home that has the device you’d like to remove.
    Nest menu highlighted
  3. Tap the device you’d like to remove on the app home screen.
  4. Tap the Settings icon in the upper right hand corner.
    Nest menu, settings icon highlighted
  5. Scroll down and select Remove.
  6. You’ll then be asked to confirm your choice.
    Nest menu, remove thermostat button highlighted
  7. You'll get an email from Nest to confirm the camera has been removed from your account.
  8. The device has been removed from the Nest account.

2 Factory Reset

If you have a Nest Aware subscription, do not cancel it if you intend to continue using your camera.

  1. Insert the release tool (or a paperclip) into the hole at the bottom of Hello and pull it from the base.
    Nest Hello being remove with the release tool.
  2. Using the release tool, hold down the reset button on the back and at the same time, hold down the doorbell button on the front for about 10 seconds.
    Hello with front and rear buttons held down.
  3. The camera will chime as its light ring spins blue, then flashes yellow.
    Light ring spins blue.
  4. When the lights turn off, release the two buttons.
  5. The camera will chime again while the light ring pulses blue to indicate the factory reset is complete.
    Light ring pulses blue.
  6. Factory reset is complete. If you want to reconnect the camera to the app, go through the setup once again.

? Do you need help getting Hello set up again?

  1. Yes
  2. No

We're here to help!

Connect to a Tech Pro

Call or chat with a Tech Pro 24/7.

This guide will assist you in performing a factory reset on your Nest Hello Video Doorbell. You may wish to do this if your device is not working as intended and you've exhausted all other possible repair steps or you want to give it to someone else.

Factory resetting your camera will erase all your camera’s settings and options. It will not automatically reconnect to Wi-Fi.

You will need:

  • The release tool (or unfolded paper clip)

You can remove your Nest device (Thermostat, Cam, Dropcam, etc) from your Nest Account within the Nest app. Whether you’re using a computer or mobile phone, the steps are the same.

  1. To remove a Nest device from your Nest Account, log into your account with the Nest app.
  2. If you have multiple homes registered on the app, tap the Menu icon in the top left corner of the app home screen, then select the home that has the device you’d like to remove.
    Nest menu highlighted
  3. Tap the device you’d like to remove on the app home screen.
  4. Tap the Settings icon in the upper right hand corner.
    Nest menu, settings icon highlighted
  5. Scroll down and select Remove.
  6. You’ll then be asked to confirm your choice.
    Nest menu, remove thermostat button highlighted
  7. You'll get an email from Nest to confirm the camera has been removed from your account.
  8. The device has been removed from the Nest account.

If you have a Nest Aware subscription, do not cancel it if you intend to continue using your camera.

  1. Insert the release tool (or a paperclip) into the hole at the bottom of Hello and pull it from the base.
    Nest Hello being remove with the release tool.
  2. Using the release tool, hold down the reset button on the back and at the same time, hold down the doorbell button on the front for about 10 seconds.
    Hello with front and rear buttons held down.
  3. The camera will chime as its light ring spins blue, then flashes yellow.
    Light ring spins blue.
  4. When the lights turn off, release the two buttons.
  5. The camera will chime again while the light ring pulses blue to indicate the factory reset is complete.
    Light ring pulses blue.
  6. Factory reset is complete. If you want to reconnect the camera to the app, go through the setup once again.
Show Me How

Clicking this button will open a new guide that will provide you with steps to resolve your issue.

We use cookies on our website to enhance your experience, analyze site usage and support our marketing efforts. To learn more, visit our Privacy Policy. By clicking “Accept”, you agree to our use of cookies and similar technologies.
Accept